/ Register

Search Results

Search Again
Page 1 of 5
  1. MCiN7
    Post

    Project VTR250

    http://www.timdoyle.net.au/pdfs/VTR250_Workshop_Manual.pdf
    Post by: MCiN7, Oct 12, 2020 in forum: Your 250cc Projects
  2. MCiN7
    Post

    Project VTR250

    You can see how bad the fluid was, this bottle had some clean brake fluid in it too [ATTACH]
    Post by: MCiN7, Sep 30, 2020 in forum: Your 250cc Projects
  3. MCiN7
    Post

    Project VTR250

    Got RWC booked in next month - found a baffle that fits in this dented muffler, I restricted the baffle some more too. Also need to change the...
    Post by: MCiN7, Sep 29, 2020 in forum: Your 250cc Projects
  4. MCiN7
    Post

    Project VTR250

    Some updates - I got everything buttoned up that I could, tied all the wiring into place, cleaned all tubing and lubed all cables (except the...
    Post by: MCiN7, Sep 21, 2020 in forum: Your 250cc Projects
  5. MCiN7
    Post

    Project VTR250

    So I was correct, just need to route the fuel line and vacuum through the right gap, thanks YouTube [ATTACH]
    Post by: MCiN7, Sep 19, 2020 in forum: Your 250cc Projects
  6. MCiN7
    Post

    Project VTR250

    Nope, wasn't too bad getting it out it was putting it back in. The only issue I have now is that I forgot where the vacuum system is supposed to...
    Post by: MCiN7, Sep 19, 2020 in forum: Your 250cc Projects
  7. MCiN7
    Post

    Project VTR250

    Some updates :) My paint booth [ATTACH] [ATTACH] [ATTACH] [ATTACH] How it sits as of tonight [ATTACH] Waiting on handlebars and tyres to...
    Post by: MCiN7, Sep 18, 2020 in forum: Your 250cc Projects
  8. MCiN7
    Thread

    Project VTR250

    Hi all! I'm back with another project. I picked up this VTR250 unregisted. Had 22###km on the clock but has been outside it's whole life and it...
    Thread by: MCiN7, Sep 14, 2020, 15 replies, in forum: Your 250cc Projects
  9. MCiN7
    Post

    (QLD) CBR250RRN Newbie

    Here you go @pwo9 No gap on the axle, perfect alignment between the caliper housing and brake disc [ATTACH] [ATTACH] [ATTACH] [ATTACH]
    Post by: MCiN7, Aug 17, 2015 in forum: Your 250cc Projects
  10. MCiN7
    Post

    (QLD) CBR250RRN Newbie

    FYI the axle bolt tightness has nothing to do with fork positioning and alignment
    Post by: MCiN7, Aug 17, 2015 in forum: Your 250cc Projects
  11. MCiN7
    Post

    (QLD) CBR250RRN Newbie

    Nope, once you move the forks closer the gap will increase between the caliper housing and the brake disc which is what you want
    Post by: MCiN7, Aug 17, 2015 in forum: Your 250cc Projects
  12. MCiN7
    Post

    (QLD) CBR250RRN Newbie

    The brake caliper housing should NOT be touching the disk, that's what the mark is on the inside of your LHS disk. Loosen the forks and wheel...
    Post by: MCiN7, Aug 17, 2015 in forum: Your 250cc Projects
  13. MCiN7
    Post

    NC29 CBR400RR

    Awesome!!
    Post by: MCiN7, Jul 25, 2015 in forum: Other Projects - Other Bikes (non 250's)
  14. MCiN7
    Post

    Matt's CBR250RR(N) 1993

    Cheers! Haha. Yep, two days in a row during winter...amazing
    Post by: MCiN7, Jul 19, 2015 in forum: Your 250cc Projects
  15. MCiN7
    Post

    Matt's CBR250RR(N) 1993

    Thanks for that info Blair! Here's some more photos of the MC22, enjoy! Note that one side is completely polished, (left side, seen in photos),...
    Post by: MCiN7, Jul 19, 2015 in forum: Your 250cc Projects
  16. MCiN7
    Post

    Matt's CBR250RR(N) 1993

    $120 for 6 runs, could have got a $55 run somewhere else but it's a fair bit out of the way. I'm not sure if I want to run slightly smaller main...
    Post by: MCiN7, Jul 19, 2015 in forum: Your 250cc Projects
  17. MCiN7
    Post

    Matt's CBR250RR(N) 1993

    Yep, Unifilter, Shorty bolt on, 110 108 108 110 mains. Pilot at 2 turns, odo at 785##km's
    Post by: MCiN7, Jul 17, 2015 in forum: Your 250cc Projects
  18. MCiN7
    Post

    Matt's CBR250RR(N) 1993

    Okay so bike went on the dyno today, I'm running rich, it's low 12's idle, 1/4, 1/2, 3/4 and full throttle. There's no flat spots which I'm happy...
    Post by: MCiN7, Jul 17, 2015 in forum: Your 250cc Projects
  19. MCiN7
    Post

    Info Jetting up a MC22 for improved performance

    Yeah got it booked in for Friday afternoon for a readout :)
    Post by: MCiN7, Jul 14, 2015 in forum: Honda 250cc In-line 4's
  20. MCiN7
    Post

    Info Jetting up a MC22 for improved performance

    I did, just going off a dyno that I've seen that had the printout for AFR's with unifilter, xcite shorty and 110+108's
    Post by: MCiN7, Jul 14, 2015 in forum: Honda 250cc In-line 4's
Showing results 1 to 20 of 95 Next >
Search Again
Page 1 of 5