1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Help No final drive.

Discussion in 'Hyosung 250cc' started by Rob1976, Apr 7, 2018.

Thread Status:
Not open for further replies.
  1. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    I've broken something but have no idea what. I was riding home the other day and being a little too agressive down shifting for a corner when i had a sudden loss of drive. The engine still runs fine and i can hear the click from each of the gears but have no drive to the wheel. I have removed the clutch cover and checked the gears that connect the engine to the clutch and gearbox, everything is fine there. So as a guess and fear is that it might be a broken shaft some where.
     
  2. ruckusman

    ruckusman White Mans Magic Master Premium Member Dirty Wheel Club

    Messages:
    3,225
    Likes Received:
    1,415
    Trophy Points:
    918
    Joined:
    Oct 1, 2013
    Gender:
    Male
    Location:
    Narrabeen, NSW Australia
    My Bike:
    Yamaha FZR250 3LN1
    Well I had something similar happen on my FZR250 - the retaining nut for the sprocket made it's way free and then the sprocket made it's way off of the shaft splines to the end where the thread used to live
     
  3. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    :headbang: I never thought to look at the sprocket.
     
  4. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    yup missing the sprocket retaining nut. :oops:

    20180407_135703.jpg
     
  5. Andych

    Andych Moderator Staff Member Premium Member Contributing Member Dirty Wheel Club

    Messages:
    4,289
    Likes Received:
    2,504
    Trophy Points:
    918
    Joined:
    Oct 6, 2016
    Gender:
    Male
    Location:
    Albury 2641
    My Bike:
    1987 Yamaha SRX250, Honda 1974 SL125 K1, 2022 Triumph Tiger Sport 660
    Hope it hasnt chewed out the threads on the output shaft...
     
  6. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    yeah they've been rounded off

    20180407_141403.jpg
     
    • Bummer Bummer x 1
  7. GreyImport

    GreyImport Administrator Staff Member The Chief Contributing Member

    Messages:
    10,914
    Likes Received:
    6,708
    Trophy Points:
    1,168
    Joined:
    Jun 14, 2012
    Gender:
    Male
    Occupation:
    Between a Rock and a Hard Place
    Location:
    North by NW NSW Oztralia - Tamworth
    My Bike:
    *Kawasaki ZXR250C *Yamaha FZR250R 3LN1 *Yamaha FZR400 *Triumph Bonneville 750 T140V *Triumph Daytona 675 *Triumph Tiger 800XC
    Did it have a lock washer fitted?
     
  8. ruckusman

    ruckusman White Mans Magic Master Premium Member Dirty Wheel Club

    Messages:
    3,225
    Likes Received:
    1,415
    Trophy Points:
    918
    Joined:
    Oct 1, 2013
    Gender:
    Male
    Location:
    Narrabeen, NSW Australia
    My Bike:
    Yamaha FZR250 3LN1
    Unfortunately you need a new output shaft by the look of things
     
  9. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    Looking at old pictures there wasn't one on it when i bought the bike.

    Yeah it's looking that way.
     
    • Bummer Bummer x 2
  10. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,313
    Likes Received:
    2,383
    Trophy Points:
    898
    Joined:
    Jun 18, 2016
    Gender:
    Male
    Occupation:
    Panel Beater, Spray Painter, Custom Fabricator
    Location:
    Adelaide, South Australia
    My Bike:
    Yamaha's , 1990 FZR250R 3LN3 , 1986 XT250TS 57R , 1984 IT200L 43G, 1976 IT400C 510
    Last edited: Apr 7, 2018
  11. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    Thanks.
     
  12. Murdo

    Murdo The Good Doctor Staff Member Contributing Member Ride and Events Crew

    Messages:
    6,397
    Likes Received:
    4,786
    Trophy Points:
    1,148
    Joined:
    May 4, 2013
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Tamworth, NSW
    My Bike:
    1937 Royal Enfield 250, CF Moto 250 V5, Honda's XL250, CBR250, FT500 plus a few others.
    That shaft would have enough splines left to go for a little while if you took it gently.
     
  13. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,313
    Likes Received:
    2,383
    Trophy Points:
    898
    Joined:
    Jun 18, 2016
    Gender:
    Male
    Occupation:
    Panel Beater, Spray Painter, Custom Fabricator
    Location:
    Adelaide, South Australia
    My Bike:
    Yamaha's , 1990 FZR250R 3LN3 , 1986 XT250TS 57R , 1984 IT200L 43G, 1976 IT400C 510
    There is a Hyosung GT250R on gumtree atm $600, if you want to keep the bike. swap engine's and get some spare's
    Probably get it cheaper too
     
  14. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    Yeah i saw that. Ive contacted the seller just waiting on a reply
     
  15. Mike Fulcher

    Mike Fulcher Active Member

    Messages:
    118
    Likes Received:
    38
    Trophy Points:
    53
    Joined:
    Feb 3, 2018
    Gender:
    Male
    Occupation:
    Owner of Mikes Chainsaws & Outdoor Power Ltd
    Location:
    New Plymouth New Zealand
    My Bike:
    85' Yamaha SRX 250, 87' Honda VT250, 86' Suzuki NZ 250, 87' Honda CBX 250, 74' Yamaha AGR100R Racer
    Look I agree with Murdo, there is plenty of spline left to keep you going, clean the spline & the inside of the sprocket thoroughly, & apply Loctite 262 (Red) to the splines & retaining nut, & yes fit the correct lock washer, that is a washer that is splined on the inside & once tightened to the correct torque figure you use a punch to fold an external edge up over one of the flat edges of the nut. Then wait for at least 8 hours for the loctite to cure before using the bike.
     
  16. Rob1976

    Rob1976 Active Member

    Messages:
    121
    Likes Received:
    70
    Trophy Points:
    53
    Joined:
    Oct 25, 2017
    Gender:
    Male
    Location:
    Adelaide
    My Bike:
    Hyosung gt250r
    Unfortunately only the first 2 threads arn't damaged. All the others have been rounded off when the sprocket came off the splines. I think trying to get adequate tension would only strip them.
     
  17. Wozza

    Wozza Active Member

    Messages:
    361
    Likes Received:
    191
    Trophy Points:
    148
    Joined:
    Mar 21, 2017
    Gender:
    Male
    Location:
    South Australia
    My Bike:
    GB250
    If your going to replace the motor tack weld a new sprocket on..if you decide to later to do repairs/rebuild just grind it off as the shaft is a total loss
     
    • Agree Agree x 2
  18. Murdo

    Murdo The Good Doctor Staff Member Contributing Member Ride and Events Crew

    Messages:
    6,397
    Likes Received:
    4,786
    Trophy Points:
    1,148
    Joined:
    May 4, 2013
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Tamworth, NSW
    My Bike:
    1937 Royal Enfield 250, CF Moto 250 V5, Honda's XL250, CBR250, FT500 plus a few others.
    Was going to suggest that but didn't want to be thought of as 'rough'. :lolsign:
     
  19. Wozza

    Wozza Active Member

    Messages:
    361
    Likes Received:
    191
    Trophy Points:
    148
    Joined:
    Mar 21, 2017
    Gender:
    Male
    Location:
    South Australia
    My Bike:
    GB250
    I like to think of in terms of "Necessity is the mother of invention" :D

    or for the more intellectual ones

    “Necessity is the mother of invention is a silly proverb. Necessity is the mother of futile dodges is much closer to the truth. The basis of growth of modern invention is science, and science is almost wholly the outgrowth of pleasurable intellectual curiosity.”
    ―Alfred North Whitehead
     
    Last edited: Apr 8, 2018
  20. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,313
    Likes Received:
    2,383
    Trophy Points:
    898
    Joined:
    Jun 18, 2016
    Gender:
    Male
    Occupation:
    Panel Beater, Spray Painter, Custom Fabricator
    Location:
    Adelaide, South Australia
    My Bike:
    Yamaha's , 1990 FZR250R 3LN3 , 1986 XT250TS 57R , 1984 IT200L 43G, 1976 IT400C 510
    So you're saying weld it, and flog it off ?
     
Thread Status:
Not open for further replies.

Share This Page