/ Register

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Content by Dave H

  1. Dave H
    Post

    Fork Oil

    I run 10w fork oil in mine, but 15 would give it a bit more stiffness without changing the springs. Hope that helps
    Post by: Dave H, Mar 26, 2015 in forum: Suzuki 250cc Twins
  2. Dave H
    Post

    Project Another GSX 250 CafeRacer

    Its been a while since I was here last The jets have been changed to a 118 main and 120 pilot, runs well, no flatspots. :) Got clocked at $1.20...
    Post by: Dave H, Jan 19, 2015 in forum: Your 250cc Projects
  3. Dave H
    Post

    Project Another GSX 250 CafeRacer

    [ATTACH] This is the running but almost finished effort. There is always something that needs to be changed or modified on this type of project.. :)
    Post by: Dave H, Nov 20, 2014 in forum: Your 250cc Projects
  4. Dave H
    Post

    Project Another GSX 250 CafeRacer

    Sorry its been so long between posts, its sort of been a bit hectic here. The little racer was finished in time for the DGR in Melbourne and...
    Post by: Dave H, Nov 17, 2014 in forum: Your 250cc Projects
  5. Dave H
    Post

    Project Another GSX 250 CafeRacer

    Well its been a while, the GSX has sat in the garage under a cover while I accumulate some $ to get the paint. Fired it up last week for the...
    Post by: Dave H, Sep 11, 2014 in forum: Your 250cc Projects
  6. Dave H
    Post

    1985 GSX250 Pub/Cafe Racer Project

    Familiar looking motor :) I found Mick Hone good for parts, apparently they have the biggest parts inventory of any Suzi dealer in Aus. I envy you...
    Post by: Dave H, Jun 24, 2014 in forum: Your 250cc Projects
  7. Dave H
    Post

    Project Another GSX 250 CafeRacer

    I promised some photos, excuse the quality, I used my phone. As it sits at the moment. Waiting for the new rims, the hubs have new bearings, and...
    Post by: Dave H, Jun 23, 2014 in forum: Your 250cc Projects
  8. Dave H
    Post

    Project Another GSX 250 CafeRacer

    Well I tested the electrics tonight, apart from a loose connection for the front brake all works well. The horn sounds like a Noddy car, a bit of...
    Post by: Dave H, Jun 11, 2014 in forum: Your 250cc Projects
  9. Dave H
    Post

    Project Another GSX 250 CafeRacer

    More progress has been made, the tank has been filled and primed ready for paint, as is the front guard. Replacement stator has been purchased...
    Post by: Dave H, Jun 10, 2014 in forum: Your 250cc Projects
  10. Dave H
    Post

    Project Another GSX 250 CafeRacer

    So the re-assembly is going in the right direction, motor has had new rings, valve stem seals, valve re-lapped ( they didn't need grinding). I...
    Post by: Dave H, Jun 5, 2014 in forum: Your 250cc Projects
  11. Dave H
    Post

    Project Another GSX 250 CafeRacer

    Motor assembly underway, new rings, valve stem seals, gaskets. Valves lapped and checked. Started to polish the cases, started to fill all the...
    Post by: Dave H, May 26, 2014 in forum: Your 250cc Projects
  12. Dave H
    Post

    Project Another GSX 250 CafeRacer

    Swing arm bushes and spacer got made today, the bushes will get case hardened through a mate in the business. So a bit more is accomplished. My...
    Post by: Dave H, May 6, 2014 in forum: Your 250cc Projects
  13. Dave H
    Post

    Bearing puller?

    If that black circular object in the picture, on the red checker plate, is the one in question. I hate to say it but that is an oil seal, not a...
    Post by: Dave H, May 6, 2014 in forum: Kawasaki 250cc In-line 4's
  14. Dave H
    Post

    Project Another GSX 250 CafeRacer

    Well the bike is now in bits spread across the garage floor. The swing arm bearings hadn't seen grease since new and are absolutely fragged, as...
    Post by: Dave H, May 2, 2014 in forum: Your 250cc Projects
  15. Dave H
    Post

    Project Another GSX 250 CafeRacer

    As is apparent, the dark marks are actually depressions in the basket caused by the plates. One side is worse than the other, but with the...
    Post by: Dave H, Apr 24, 2014 in forum: Your 250cc Projects