/ Register

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

made this..

Discussion in 'Yamaha 250cc In-Line 4's' started by rb89, Nov 21, 2006.

  1. rb89

    rb89 New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    May 23, 2006
    a while back i needed a stand and didnt know about the ratchet strap method, anyway, ive got some but i needed to fill in time yesturday so this is what i came up with

    [​IMG]
     
    rb89, Nov 21, 2006
    #1
  2. 8_stitch

    8_stitch New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    Mar 28, 2006
    looks well made
    are you going to add a handle?
     
    8_stitch, Nov 21, 2006
    #2
  3. Ciaran

    Ciaran New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    Nov 5, 2004
    Doesn’t it already have a handle?

    I admire homebrew projects, mainly because I never seem to have enough time / expertise / tools to do it well myself.

    Well done. Bet you saved a few quid as well.
     
    Ciaran, Nov 21, 2006
    #3
  4. FZR Dude

    FZR Dude New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    Mar 24, 2004
    Well done.
     
    FZR Dude, Nov 21, 2006
    #4
  5. Spook

    Spook New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    Sep 26, 2004
    now you just need to put some dolly wheels on the pivot points and start flogging them on ebay for $100! nice work.
     
    Spook, Nov 21, 2006
    #5
  6. rb89

    rb89 New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    May 23, 2006
    The handle's the end part and im looking for the right sized little wheels... but i think im gunna make another one soon and with a bit more design cause this one fits me PE175 too.
    i seen them on ebay for 130ish and figured why not make one
     
    rb89, Nov 22, 2006
    #6
  7. 8_stitch

    8_stitch New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    Mar 28, 2006
    you have inspired me to make my own now because i need to service the rear end
    lets just hope it dosnt do what my last fabrication project did and empty my wallet
     
    8_stitch, Nov 22, 2006
    #7
  8. rb89

    rb89 New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    May 23, 2006
    the only cost this one hit me with was $25 for wiring to get the old welder kicking again!
     
    rb89, Nov 22, 2006
    #8
  9. 8_stitch

    8_stitch New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    Mar 28, 2006
    did you use a pipe bender?
     
    8_stitch, Nov 22, 2006
    #9
  10. seifer

    seifer New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    Jun 6, 2005
    How'd ur HSC go, with a stand like that i expect a UAI of atleast 96.2!
     
    seifer, Nov 22, 2006
    #10
  11. rb89

    rb89 New Member

    Messages:
    0
    Likes Received:
    0
    Trophy Points:
    0
    Joined:
    May 23, 2006
    nah no pipe bender. put the pipe in the vice and got a larger length of square pipe, slid it over it and used it for leverage to bend it . technique needs a bit of refining tho.. got a bit too much of a kink than what i was after.

    HSC...its ova. thats all ive got to say lol
     
    rb89, Nov 22, 2006
    #11

Share This Page