1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

NSR250 Parts

Discussion in 'FOR SALE' started by KICKERMAN360, Sep 18, 2015.

  1. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    Bunch of stuff as seen below except the MC21 speedo cluster. Sort of need the stuff gone ASAP. Can post (I normally use AusPost).

    MC21

    Stock rear sets - A little worse for wear but plenty of good stuff. One side is slightly bent/twisted though
    Triple Clamps
    Forks - stanchions are slightly bent
    Front axle
    Clip ons

    MC18

    Frame - Straight, has compliance plate
    Sub Frame - Straight, tabs for seat are bent down though
    Rear Caliper, Line and Caliper Mount
    Tank - Dent on the contour near the rear
    Air Box - Has holes drilled in the top cover for better air flow
    Switch Block
    Front Axle
    Swing Arm w/ chain slider
    Clip ons
    Rear Sets - The LHS one is a plate made by someone, but the other side is in good nick.
    Coolant Overflow bottle
    2 stroke oil bottle
    Swing Arm bolt
    Carburetor Solenoid
    RC Valve Servo Motor - Need to double check this one
    Ignition - Fuel tank lock, rear compartment lock and ignition barrel, one key
    Throttle Tube and cables
    Brackets for holding cables etc
    Front guard - white, paint on the rear is a little chipped but otherwise in okay condition
    Thermostat
    Pillion Seat - Cover is a little worn
    Speedo and gauges - I think the stay is a little bent but functions correctly

    IMG_1853.JPG IMG_1854.JPG IMG_1856.JPG IMG_1857.JPG
     
  2. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    Update, everything is on the GOLD COAST now. So local people, feel free to pick up anything. Or just visit and sort through things.

    MC21

    Stock rear sets - A little worse for wear but plenty of good stuff. One side is slightly bent/twisted though
    Triple Clamps
    Front axle
    Clip ons

    MC18

    Frame - Straight, has compliance plate
    Sub Frame - Straight, tabs for seat are bent down though
    Rear Caliper, Line and Caliper Mount
    Air Box - Has holes drilled in the top cover for better air flow
    Switch Block
    Front Axle
    Swing Arm w/ chain slider
    Clip ons
    Rear Sets - The LHS one is a plate made by someone, but the other side is in good nick.
    2 stroke oil bottle
    Swing Arm bolt
    Carburetor Solenoid
    Ignition - Fuel tank lock, rear compartment lock and ignition barrel, one key
    Throttle Tube and cables
    Brackets for holding cables etc
    Front guard - white, paint on the rear is a little chipped but otherwise in okay condition
    Thermostat
    Pillion Seat - Cover is a little worn
    Speedo and gauges - I think the stay is a little bent but functions correctly

    MC28

    Swing arm with axle thingy
     
  3. Fox McScrooge

    Fox McScrooge Well-Known Member Premium Member Contributing Member

    Messages:
    490
    Likes Received:
    286
    Trophy Points:
    298
    Joined:
    Aug 1, 2013
    Gender:
    Male
    Location:
    Brisbane
    My Bike:
    1996 NSR250 MC28 R2T
    Got a photo of the MC28 swingarm?
     
  4. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    I'll get it out (has to go in the NSR parts box anyway) and get a picture for you.
     
  5. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    There's a scuff in the LHS so probably not show bike material. But any reasonable offer and it's yours.

    IMG_2072[1].JPG

    IMG_2071.JPG
     
  6. Fox McScrooge

    Fox McScrooge Well-Known Member Premium Member Contributing Member

    Messages:
    490
    Likes Received:
    286
    Trophy Points:
    298
    Joined:
    Aug 1, 2013
    Gender:
    Male
    Location:
    Brisbane
    My Bike:
    1996 NSR250 MC28 R2T
    Might give it a miss thanks mate. Appreciate you taking the time to photograph it.
     
  7. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    No problem. If a decent wheel comes up I might keep it and fit it to the MC21 eventually.
     
  8. Fox McScrooge

    Fox McScrooge Well-Known Member Premium Member Contributing Member

    Messages:
    490
    Likes Received:
    286
    Trophy Points:
    298
    Joined:
    Aug 1, 2013
    Gender:
    Male
    Location:
    Brisbane
    My Bike:
    1996 NSR250 MC28 R2T
    How is the 21? Finished the build yet?
     
  9. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    I haven't touched it for over a month. I have to get this minor renovation done first, sell the CRM250, then sell the MC22, and then rebuild a CR125 motor so I can swap the engine and then sell it. Plus job hunting is the main priority right now.

    Eventually I'll get to it though.
     
  10. aky141

    aky141 Well-Known Member

    Messages:
    196
    Likes Received:
    122
    Trophy Points:
    248
    Joined:
    Jan 18, 2014
    Gender:
    Male
    Location:
    Kempsey, New South Wales
    My Bike:
    Yamaha DT200R, Honda NSR250SE
    wait wait, crm 250?
    How much <3
     
  11. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    Well, I'm hoping to get $1800 or more for it. I am waiting on some seals for the front sprocket and then I'll sell it. It's actually a nice bike, started and ran super well after not being run for 2 years. There's a trail ride coming up that I'm considering taking it on too.
     
  12. aky141

    aky141 Well-Known Member

    Messages:
    196
    Likes Received:
    122
    Trophy Points:
    248
    Joined:
    Jan 18, 2014
    Gender:
    Male
    Location:
    Kempsey, New South Wales
    My Bike:
    Yamaha DT200R, Honda NSR250SE
    pics?
     
  13. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
  14. Aaron81

    Aaron81 Active Member

    Messages:
    90
    Likes Received:
    45
    Trophy Points:
    188
    Joined:
    Nov 22, 2015
    Gender:
    Male
    Location:
    Hervey Bay
    My Bike:
    1990 Honda NTV650 Revere
    Would a mc22 rear fit it?
     
  15. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    I believe so. I can measure it tomorrow but I know for sure that NSR wheels will not fit, thanks to the sprocket carrier. The Mc22 wheels differ because they have the sprocket bolted directly to the rim and are an inch or so thinner.

    Someone did the conversion already with quite extensive medications to the CRM. I wouldn't bother with the CR250 cylinder (an overbore to 290cc would be a better idea) but converting to CR plastics was what I had planned. Here's some pics with the Mc22 wheels from that project: http://supermotojunkie.com/showthread.php?123232-Cr(m)250-supermoto-build
     
  16. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    Also not 100% sure on the axle sizes. I think the front axle needs a sleeve, I can't exactly remember. It's not a major hassle anyway. I recorded a start up of the bike yesterday but for some reason the sound didn't record so I'll try again when I get the chance.
     
  17. Aaron81

    Aaron81 Active Member

    Messages:
    90
    Likes Received:
    45
    Trophy Points:
    188
    Joined:
    Nov 22, 2015
    Gender:
    Male
    Location:
    Hervey Bay
    My Bike:
    1990 Honda NTV650 Revere
    Not to sure if it will help as you are quite some distance from where I am but I may happen to have a spare mc22 rear rim floating around not being used considering I have changed my color scheme once again on this bitsa 91 mc22 I am currently trying to plan (Trying being the operative word)
     
  18. Aaron81

    Aaron81 Active Member

    Messages:
    90
    Likes Received:
    45
    Trophy Points:
    188
    Joined:
    Nov 22, 2015
    Gender:
    Male
    Location:
    Hervey Bay
    My Bike:
    1990 Honda NTV650 Revere
    So hows the progress on the 21 have you found a decent replacement wheel for it yet?
     
  19. KICKERMAN360

    KICKERMAN360 Well-Known Member

    Messages:
    389
    Likes Received:
    294
    Trophy Points:
    273
    Joined:
    Oct 26, 2014
    Gender:
    Male
    Location:
    Melbourne/Gold Coast
    My Bike:
    CRF50, CR125, MC21,MC22,CBR600RR
    A rear wheel? Nope. I have sort of got the MC21 on hold right now. Once I get it finished with the stock swing-arm I was then gonna look at converting to an MC28. I just happen to get that swing arm when I got some other parts too. I probably haven't touched the NSR for 3 months or so but hope to get into it next week.
     
    • Like Like x 1

Share This Page