/ Register

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Search Results

Search Again
Page 1 of 10
  1. sharky
    Post

    Pinned So what have you done to your bike today?

    Try the thrust bearing in the clutch plate, they should be press fitted, most just fall out though. With the clutch pulled in, the push rod pushes...
    Post by: sharky, Oct 8, 2019 in forum: The Pub
  2. sharky
    Post

    Help Getting old tank liner out

    The companies that make these tank liners usually make another product that can strip the liner, I'm fairly certain there acetone based.
    Post by: sharky, Jul 18, 2019 in forum: Tech Tips
  3. sharky
    Post

    Project ZXR250 Resurrection.

    My advice would be to get it running before pulling everything apart, better to find the problems now than after re-assembling. Clean the carbs,I...
    Post by: sharky, May 20, 2019 in forum: Your 250cc Projects
  4. sharky
    Post

    New Member New owner, ZXR250C

    :welcome:
    Post by: sharky, May 20, 2019 in forum: New Members Say Gday
  5. sharky
    Post

    URGENT Rear Brake Master Cylinder Kit

    Heaps on EBay, but they take a few weeks delivery as their from overseas, might be easier & cheaper to get a used working spare master, @kiffsta ?...
    Post by: sharky, Apr 9, 2019 in forum: Kawasaki 250cc In-line 4's
  6. sharky
    Post

    Project Sharky's ZXR shed

    All good thanks Kiff, the other tank is fine inside, I have decided to make this a longer term project & re-paint in the tri-colour, the bike...
    Post by: sharky, Apr 3, 2019 in forum: Your 250cc Projects
  7. sharky
    Post

    Project Sharky's ZXR shed

    Covers cleaned up & motor back in the frame. [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] The bike came with 2 tanks, unfortunately the...
    Post by: sharky, Apr 2, 2019 in forum: Your 250cc Projects
  8. sharky
    Post

    New Member G'Day Balius-with-ZXR motor new owner

    :welcome: Mike
    Post by: sharky, Apr 1, 2019 in forum: New Members Say Gday
  9. sharky
    Post

    Project Sharky's ZXR shed

    Tidied up the front,rear & mainframes etc, the wheels could do with fresh paint though. [ATTACH] [ATTACH] [ATTACH] Had to get the compressor...
    Post by: sharky, Mar 31, 2019 in forum: Your 250cc Projects
  10. sharky
    Post

    Info ZXR250C Swingarm

    [ATTACH] [ATTACH] [ATTACH] [ATTACH]
    Post by: sharky, Mar 23, 2019 in forum: Kawasaki 250cc In-line 4's
  11. sharky
    Post

    Info ZXR250C Swingarm

    Haha, yeah 95% of them are like that.[ATTACH] [ATTACH] [ATTACH]
    Post by: sharky, Mar 23, 2019 in forum: Kawasaki 250cc In-line 4's
  12. sharky
    Post

    Project Sharky's ZXR shed

    Dropped the motor out & removed the whole rear end, everything is quite filthy. [ATTACH] [ATTACH] [ATTACH] Used my last seal kit on the carbs...
    Post by: sharky, Mar 20, 2019 in forum: Your 250cc Projects
  13. sharky
    Post

    Project Sharky's ZXR shed

    [ATTACH] This is the standard fusebox on most A & C models with 7 wires in the 10 pin plug (on left). Mmm interesting, 94-2008 that kinda...
    Post by: sharky, Mar 16, 2019 in forum: Your 250cc Projects
  14. sharky
    Post

    Project Sharky's ZXR shed

    Had a look over the new project & noticed the things people have tried to get it running, new plugs & filter, tci(with price still attached)...
    Post by: sharky, Mar 16, 2019 in forum: Your 250cc Projects
  15. sharky
    Post

    Help Spongy brakes ZXR250A

    Some brakes I could never pump up fully, I solved that problem with a 20ml syringe & aquarium hose, put the hose over the bleed nipple & fully...
    Post by: sharky, Mar 15, 2019 in forum: Kawasaki 250cc In-line 4's
  16. sharky
    Post

    Info DLRA 2019 Speed Week (Lake Gairdner, Australia)

    Great write-up @Frankster what an adventure it must of been. Didn't realize the salt flats could get so rough.
    Post by: sharky, Mar 12, 2019 in forum: Motorcycle Racing and Track Days
  17. sharky
    Post

    Project Sharky's ZXR shed

    Already started the next project, got this bike as a non runner last year in January the same time I got the last bike off Kiff. The bike done the...
    Post by: sharky, Mar 10, 2019 in forum: Your 250cc Projects
  18. sharky
    Post

    Project Sharky's ZXR shed

    Forgot to mention the seal kit worked a treat aswell, no flat spot around 2.5- 3000rpm now, could not get it to sit on 3000rpm.
    Post by: sharky, Mar 10, 2019 in forum: Your 250cc Projects
  19. sharky
    Post

    Project Sharky's ZXR shed

    Been waiting a few weeks for parts to arrive. I got a new cam chain tensioner for piece of mind & some new pads. A mate also got some pads & wavy...
    Post by: sharky, Mar 10, 2019 in forum: Your 250cc Projects
  20. sharky
    Post

    New Member Hi - new member here!

    :welcome:
    Post by: sharky, Mar 10, 2019 in forum: New Members Say Gday
Showing results 1 to 20 of 195 Next >
Search Again
Page 1 of 10