Help Vincent’s FZR 250 not starting...

Discussion in 'Yamaha 250cc In-Line 4's' started by Vincent, Jul 11, 2018.

Page 3 of 3
  1. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,313
    Likes Received:
    2,384
    Trophy Points:
    898
    Location:
    Adelaide, South Australia
    This is my 3LN3 TCI when i pulled it apart to replace the transistor's and capacitor's

    [​IMG] [​IMG] [​IMG]
     
    Last edited: Jul 16, 2018
    my67xr, Jul 16, 2018
    #41
  2. Vincent

    Vincent Member

    Messages:
    18
    Likes Received:
    6
    Trophy Points:
    13
    Location:
    Canada
    That is some detailed work you have done. I’ll open my TCI and compare. I really appreciate all the help from everyone here . Thank you sincerely
    Cheers
    Vince
     
    • Like Like x 1
    Vincent, Jul 17, 2018
    #42
  3. Farklepilot

    Farklepilot Active Member

    Messages:
    10
    Likes Received:
    7
    Trophy Points:
    73
    Location:
    Vancouver Island
    Old thread... decided best I bring it back as I now own this bike. Has been sitting for some time. Front caliber is dragging. Is there a preferred rebuild kit or even better, replacement caliper I should source? Here in Canada.... Understood it would probably have to come from Europe or Asia. Would like to replace the fuel filter as well. Can not seem to locate one?
     
    Farklepilot, Apr 19, 2020
    #43
  4. ruckusman

    ruckusman White Mans Magic Master Premium Member Dirty Wheel Club

    Messages:
    3,274
    Likes Received:
    1,435
    Trophy Points:
    918
    Location:
    Narrabeen, NSW Australia
    That's why I won't date good looking fuses nowadays, they just leave you feeling flat by the end
     
    ruckusman, Apr 19, 2020
    #44
  5. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,313
    Likes Received:
    2,384
    Trophy Points:
    898
    Location:
    Adelaide, South Australia
    my67xr, Apr 19, 2020
    #45
  6. Farklepilot

    Farklepilot Active Member

    Messages:
    10
    Likes Received:
    7
    Trophy Points:
    73
    Location:
    Vancouver Island
    Thanks! There on the way... Have carbs off and somewhat apart. Quite the backyarding happened in there! Needle caps for instance... Two of them are actually home made drilled out screws! Decided to redo them all. New float needle and seats, new kit from Litetek etc etc.. Will be a while waiting for parts.
     
    • Like Like x 1
    Farklepilot, May 13, 2020
    #46
  7. Sammy LYLE

    Sammy LYLE Member

    Messages:
    13
    Likes Received:
    12
    Trophy Points:
    13
    Location:
    New Zealand
    What do SS and FP stand for?I am assuming SideStand for SS, but not sure of FP. Are these lockout switches? If so, how would I trick them into letting the engine run? I am using the engine in a Kart with total-loss battery supply to run the engine (no alternator) and a simple racing wiring loom. Does the neutral-indicator lockout affect the ECU?
     
    Sammy LYLE, Jan 26, 2022
    #47
  8. ruckusman

    ruckusman White Mans Magic Master Premium Member Dirty Wheel Club

    Messages:
    3,274
    Likes Received:
    1,435
    Trophy Points:
    918
    Location:
    Narrabeen, NSW Australia
    Speculation - SS is likely side stand, it makes sense

    Don't quote me on this, but I recall that the clutch switch let's the engine start in gear, but the side stand switch prevents it starting in gear, so the neutral gear position switch in conjunction with the side stand switch prevents starting

    I don't have access to my bike to check the side stand switch
     
    • Like Like x 1
    ruckusman, Jan 26, 2022
    #48
Page 3 of 3

Share This Page