QLD ZXR250 Water Pump Shaft

Discussion in 'WANTED' started by DanoHosko, May 12, 2020.

  1. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Ok fairly desperate for a new water pump shaft
    13107-1271

    Im in Mackay QLD, happy to pay postage and for the shaft!

    I got the new water pump and oil seals arriving this week but just realised the shaft is heavily pitted and not convinced an oil seal will last long...
    (It was leaking coolant but not oil before though)

    Have emailed local Kawasaki, none in stock here or Sydney so will be back order to Japan

    I believe oil seal is 10mm ID, shaft i i wanna say 11mm, so might have a go with some grit paper...




    Cheers!

    Dan

    DSC_0449.JPG
     
    Last edited: May 12, 2020
  2. 2valve

    2valve Well-Known Member

    Messages:
    861
    Likes Received:
    352
    Trophy Points:
    348
    Location:
    Glen Innes Australia
    • Agree Agree x 1
  3. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Yep looks like the one to me!

    Thanks for that, I'll have to message them, from what I've heard not much is coming into Aus from Japan at the moment :(
     
  4. 2valve

    2valve Well-Known Member

    Messages:
    861
    Likes Received:
    352
    Trophy Points:
    348
    Location:
    Glen Innes Australia
    Hi Dan
    No problem , happy to help. The part is in Japan though , but if your in a hurry for it , it may be an option for you. At'least you'll have one. Keep looking via the web just in case one may be closer.
     
  5. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    I might get hold of a machinist in town see if they can make one up but i imagine it will be a fortune

    Ebay probably be the go ;)
    Cheers again!
     
  6. 2valve

    2valve Well-Known Member

    Messages:
    861
    Likes Received:
    352
    Trophy Points:
    348
    Location:
    Glen Innes Australia
    I thought that also about inquiring about getting one machined up , than i had a look over the one in the link.I'd imagine the shaft would be tempered anyway. I think i'd just buy a new O.E one. At'least it would be correct and bolt straight up to get you going.
    No problem buddy , happy shopping.
     
    • Agree Agree x 1
  7. Andych

    Andych Moderator Staff Member Premium Member Contributing Member Dirty Wheel Club

    Messages:
    4,300
    Likes Received:
    2,514
    Trophy Points:
    918
    Location:
    Albury 2641
  8. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Ah yeah i briefly entertained the idea of the speedy sleeves, i got a mate at a bearing joint I'll see what he reckons

    Concern is whether i can get a sleeve that the pump housing can fit over also so i can still take it off
     
  9. Murdo

    Murdo The Good Doctor Staff Member Contributing Member Ride and Events Crew

    Messages:
    6,406
    Likes Received:
    4,795
    Trophy Points:
    1,148
    Location:
    Tamworth, NSW
    What about building the shaft up with weld and remachining to correct size.
     
    • Agree Agree x 1
  10. Andych

    Andych Moderator Staff Member Premium Member Contributing Member Dirty Wheel Club

    Messages:
    4,300
    Likes Received:
    2,514
    Trophy Points:
    918
    Location:
    Albury 2641
    Depending on how easy it is to get the shaft out I would take it to either a bearing store or find a metal sprayer in town.. It is Mackay after all..should be plenty of shops there that can do what you want.. but as you say it is the $$ that will make the difference.
    Stellite sleeves are available as well.. It will never wear out then...lol
    I have had pump shafts machined down and a stainless steel sleeve fitted before or you might even find that some speedy sleeve style items are out there for old holden / ford water pump seals that might be the right size.. my memory isnt that good going back that far.
     
    • Like Like x 1
  11. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland

    True theres definitely plenty of places in Mackay that should be able to help, I'll speak to one of the engine reconditioning places and see who/what they reckon ;)
     
  12. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Can't seem to see shaft removal in the workshop manual

    Do i just need to remove the clutch and then circlip and dowel pin?
     
  13. Andych

    Andych Moderator Staff Member Premium Member Contributing Member Dirty Wheel Club

    Messages:
    4,300
    Likes Received:
    2,514
    Trophy Points:
    918
    Location:
    Albury 2641
    Can you remove the complete Water pump housing from the transmission? If so the shaft should come out with it and you should then be able to remove the shaft.
     
  14. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Got the water pump and housing and oil pump off it

    Looks like shaft held by circlip at the clutch end to me
    47ebe3c97095a5728a9734298e1cd27a.png
     
  15. Andych

    Andych Moderator Staff Member Premium Member Contributing Member Dirty Wheel Club

    Messages:
    4,300
    Likes Received:
    2,514
    Trophy Points:
    918
    Location:
    Albury 2641
    Looks like a fair bet to me...
     
  16. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,313
    Likes Received:
    2,384
    Trophy Points:
    898
    Location:
    Adelaide, South Australia
    • Like Like x 1
  17. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Ahhh good shout! didnt didnt to look for people breaking bikes on ebay :D

    Handsonkawasaki looks like they have none in stock when i i check before, might ping them an email
     
  18. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Sorry to turn this into another help me thread...

    Clutch plates, how many should there be?

    I have 6 fibre and 6 metal plates, two metal plates are next to each other in the stack


    Also cant get the clutch basket off ahha
     
  19. ruckusman

    ruckusman White Mans Magic Master Premium Member Dirty Wheel Club

    Messages:
    3,273
    Likes Received:
    1,435
    Trophy Points:
    918
    Location:
    Narrabeen, NSW Australia
    One possibility to repair the pitting in the shaft you have is cold welding, also called electro deposition welding

    I bumped across it last week

    This is one example


    The handle/electrode he is holding is like a dremel of sorts, spinnng the metal to be deposited in the welds and it applies tiny amounts without much heating at all and is used specifically to address issues like you have with your water pump shaft

    Lots of other examples on youtube
     
  20. DanoHosko

    DanoHosko Well-Known Member Premium Member

    Messages:
    249
    Likes Received:
    96
    Trophy Points:
    228
    Location:
    Brisbane, Queensland
    Interesting but not sure I'd be able to find anyone who could do that near me that i i would trust haha

    So far:
    - local engine reco place quoted $350 to repair/replace the shaft
    - Two other places have not provided quotes to machine a new one until they see the original
    - when i can get clutch out and shaft will take it to my bearing mate see about speedi sleeve options
    - my mate in UK reckons he can get a new one to him like next day so if UK-Aus delivery is still happening that might be an option
    - can't find definitive answers as to what if any air freight is coming from Japan still (tnt/fedex/ems?)


    - Broke the clutch plate holder/hub with my heavy handedness and the fact the clutch nut is tight as hell (still stuck on there)
     

Share This Page