Frames painted, not perfect but doesn't look too bad. Just gonna focus on getting it back together for now, got most of the body work ready for colour just painted with white underfoot for now and stored somewhere safe, gonna work on the suspension next. Sent from my SM-G973F using Tapatalk
One wheel done. Rest of the bike was gonna be too black so think I'll go for the bright wheels so I can be seen better. I'll put the old tyres back on while I'm working on it but they 12 years old so will have to get new ones before she hits the streets. Sent from my SM-G973F using Tapatalk
Looks even better with the rubber on her and fitted onto the rear. Sent from my SM-G973F using Tapatalk
So just did a valve check with the cams in the right place. Intake is within specs but exhaust is too tight. I have watched a video on how to shim them but don't know where to get the shims. if I figure out what's in there atm and what i need I should be able to get them from any bike shop or would I be better sticking with my guy at Yamaha? Sent from my SM-G973F using Tapatalk
You want to remove the cams, and use a magnetic lifter to remove the buckets, then record what thickness shim you've got underneath each bucket - hopefully they have all been installed with the etched number facing upwards otherwise it might be obscured from being in contact with the top of the valve and wearing out on this page there's two documents to download to record the values, then it's just simple arithmetic to calculate the reduction in shim thickness required - go to the upper limit of clearance then shuffle whatever you have and work out what you need https://www.2fiftycc.com/index.php?threads/fzr250-zeal-fzx250-valve-clearances-howto.1697/ I believe @kiffsta produced a better version of the clearance recording page somewhere, well I've seen it and I think it's better than mine www.precisionshims.com.au is the place to get them, usually order one day and receive them the next
To accurately measure shims you need an inside micrometer, 0-25mm range, often the numbers printed on top are not totally accurate. They will be 7.48mm OD shims, the same as most jap inline 4's With shim and bucket setup, clearance decreases over time due to wear*. Therefore it is ideal to set all clearances to the maximum allowed with the engine cold. Not only does this improve performance, it gives you maximum time between adjustments. If you notice a valve with excessive clearance, it is likely that either the valve stem tip is wearing, or you have carbon/debris on the valve seat. *Other systems like Ducati's desmodromic system loosen over time.
Apparently it got new valves when it was torn down. Wouldn't the wear increase the gap over time? So wouldn't it make sense to go for the lower to mid spec? Sent from my SM-G973F using Tapatalk
Valves and seats as they wear - the stem effectively gets longer and the clearance reduces, which is why you need to go to thinner shims to increase the clearance, and especially given that your valves are new, they will seat and that clearance will reduce quickly to begin with - take them to maximum clearance
Oh right of course. That makes sense. So I'd wanna go as close to the upper spec and allow the new valves time to seat in properly. Sent from my SM-G973F using Tapatalk
Correct. After you set the clearances, you should also tune the mixture screws and balance the carbs for optimum performance.
Clearances are all exactly 0.01 below the max tolerances timing is set right and engine is now bolted in. Gotta get exhaust gaskets on Tuesday and new chain and sprokets. In the meantime something electrical and cooling. But progress is being made. Big smiles Sent from my SM-G973F using Tapatalk
Sensational work, I was at first a little skeptical that given all of the hassle you had with the engine, that it would drain your enthusiasm and you'd lose the motivation to keep charging with all of the cosmetics Very glad I was wrong about that, and to boot, you've got the mechanical elements sorted, so once it's back together it's ride time!!
Yeah man, still gotta call up the bike wreckers and see if the can ship me some parts. They over 50km away and still can't travel that far. Mainly need a seat, front guard and the exup cables but I get a feeling I'll have to make them up custom. Sent from my SM-G973F using Tapatalk
Starting to come together, maybe do a bit of paint over the weekend but got a new chain sprokets and brake pads today as well as some led indicators. Having a bit of trouble routing wires and cables under the cowl does anyone have a pic of the front without the cowl so I can see how it all fits in? Sent from my SM-G973F using Tapatalk
I have my whole front section off and still complete with lights and dash in the frame and cowling ... Ill take some pics t/m
Cheers brother much appreciated. Also might have to make up the exup cables. Don't suppose you know what lengths I'd need? Sent from my SM-G973F using Tapatalk