/ Register

Recent Content by zxaar

  1. zxaar
    Profile Post

    "you live more in five minutes on a bike like this going flat-out than most people do in a...

    "you live more in five minutes on a bike like this going flat-out than most people do in a lifetime" - Burt Munro.
    Status Update by zxaar, Jul 25, 2013
  2. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    Just a quick update. Motobatt battery rocked up today so I installed that, fixed a broken off bolt and fitted the fuel tank/battery bracket so...
    Post by: zxaar, Jul 22, 2013 in forum: Kawasaki 250cc In-line 4's
  3. zxaar
    Post

    Single seat cowl for ZXR250a

    Congrats man. There's no better feeling than getting that piece of paper saying your good to go. Well done:drinks:
    Post by: zxaar, Jul 22, 2013 in forum: Kawasaki 250cc In-line 4's
  4. zxaar
    Post

    Single seat cowl for ZXR250a

    Best of luck with the roadworthy tomorrow mate, let me know how you go :thumb_ups:
    Post by: zxaar, Jul 21, 2013 in forum: Kawasaki 250cc In-line 4's
  5. zxaar
    Post

    Single seat cowl for ZXR250a

    Yeah, I meant leaving the rear seat on the bike.
    Post by: zxaar, Jul 19, 2013 in forum: Kawasaki 250cc In-line 4's
  6. zxaar
    Post

    Single seat cowl for ZXR250a

    That's looks pretty nice, my bike has an LK7 plate and the rear pegs have been removed but the pillion seat is still there. Would this cause any...
    Post by: zxaar, Jul 19, 2013 in forum: Kawasaki 250cc In-line 4's
  7. zxaar
    Post

    Uh oh cam tensioner!

    Broken bits go hand-in-hand with older bikes I've learnt but fortunately Kiffsta had a spare one for ya mate :) I recently found out the screws on...
    Post by: zxaar, Jul 18, 2013 in forum: Kawasaki 250cc In-line 4's
  8. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    Thanks guys, she's gettin there now :) Just bought new brake seals(x8), a new MB9U Motobatt battery and a new helmet. Next payday I'll be getting...
    Post by: zxaar, Jul 18, 2013 in forum: Kawasaki 250cc In-line 4's
  9. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    Haha, that's not just dust/dirt. The back wheel needs to be repainted and I need to find a way to make the surface rust on some areas shine.
    Post by: zxaar, Jul 17, 2013 in forum: Kawasaki 250cc In-line 4's
  10. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    Just a quick walk-around clip from the other week after I put the new head gasket on and changed the oil/filter & coolant. [media]
    Post by: zxaar, Jul 17, 2013 in forum: Kawasaki 250cc In-line 4's
  11. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    It may have been partially covered beforehand but I am hunting a chain and I know that it needs to be 520 pitch but does it matter if it is an o...
    Post by: zxaar, Jul 17, 2013 in forum: Kawasaki 250cc In-line 4's
  12. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    In regard to the brake calliper seals which come in sets of four would both the left and right seals be the same? I only ask because an Ebay...
    Post by: zxaar, Jul 17, 2013 in forum: Kawasaki 250cc In-line 4's
  13. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    I don't have a compressor yet but did a bit of a bleed and managed to get one piston out. It was kinda hard when I was holding the lever and brake...
    Post by: zxaar, Jul 13, 2013 in forum: Kawasaki 250cc In-line 4's
  14. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    I pulled the front brakes apart this morning and gave the whole lot a clean-up but the pistons are stuck and I cannot get them out at all. I have...
    Post by: zxaar, Jul 13, 2013 in forum: Kawasaki 250cc In-line 4's
  15. zxaar
    Post

    Shaun's ZXR250 A model Build Thread

    $88 inc. postage
    Post by: zxaar, Jul 11, 2013 in forum: Kawasaki 250cc In-line 4's