1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Help Banjo bolt brake line - Honda Spada

Discussion in 'Honda 250cc Twins' started by Dirttrev, Apr 13, 2019.

  1. Dirttrev

    Dirttrev Member Premium Member

    Messages:
    19
    Likes Received:
    8
    Trophy Points:
    13
    Joined:
    Mar 17, 2019
    Gender:
    Male
    Location:
    New Zealand
    My Bike:
    Honda VT250 Spada 1990
    Hi, anyone know if the brake line banjo bolt size on Honda Spada M10x1.25 or M10x1.0 thread size?, like to order a brake pressure switch, but don't want to strip and bleed just yet TIA
    Trevor
     
  2. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,145
    Likes Received:
    2,292
    Trophy Points:
    898
    Joined:
    Jun 18, 2016
    Gender:
    Male
    Occupation:
    Panel Beater, Spray Painter, Custom Fabricator
    Location:
    Adelaide, South Australia
    My Bike:
    Yamaha's , 1990 FZR250R 3LN3 , 1986 XT250TS 57R , 1984 IT200L 43G, 1976 IT400C 510
    • Like Like x 1
  3. Murdo

    Murdo The Good Doctor Staff Member Premium Member Ride and Events Crew Contributing Member

    Messages:
    5,566
    Likes Received:
    4,219
    Trophy Points:
    1,148
    Joined:
    May 4, 2013
    Gender:
    Male
    Occupation:
    Retired
    Location:
    Tamworth, NSW
    My Bike:
    1938 Royal Enfield 250, CF 250 V5 and 650TK, XL250, CBR250, plus a few others.
    My CBR's have M10x1.25 so guess the Spada would be same as same master cylinder.
     
    • Like Like x 1
  4. Dirttrev

    Dirttrev Member Premium Member

    Messages:
    19
    Likes Received:
    8
    Trophy Points:
    13
    Joined:
    Mar 17, 2019
    Gender:
    Male
    Location:
    New Zealand
    My Bike:
    Honda VT250 Spada 1990
    Thanks guys, I actually bought both pitches from Ali Express, only 10 NZD, my bases are covered, reason I'm lowering my foot pegs and the ole mechanical brake switch mount was cut off...
     
  5. Gizziracer

    Gizziracer Well-Known Member Premium Member Contributing Member

    Messages:
    240
    Likes Received:
    139
    Trophy Points:
    248
    Joined:
    May 7, 2017
    Location:
    Sydney
    My Bike:
    Honda vt 250 spada
    Neither the front or rear Spada brake lights operate from fluid pressure. Both are mechanical switches, new front can be purchased for less than $20 on ebay,, Rear one can almost always be repaired by carefully adjusting the spring tension. They are often too tight rather than too loose, this often tricks people into thinking they are broken
     
  6. my67xr

    my67xr Bike Enthusiast Staff Member Premium Member Contributing Member

    Messages:
    4,145
    Likes Received:
    2,292
    Trophy Points:
    898
    Joined:
    Jun 18, 2016
    Gender:
    Male
    Occupation:
    Panel Beater, Spray Painter, Custom Fabricator
    Location:
    Adelaide, South Australia
    My Bike:
    Yamaha's , 1990 FZR250R 3LN3 , 1986 XT250TS 57R , 1984 IT200L 43G, 1976 IT400C 510
    His rear brake switch mount has been cut off the frame though
     
    • Like Like x 1

Share This Page